Premium Member blackout Posted September 24, 2019 Premium Member Share Posted September 24, 2019 I'm starting a winter project soon and could use a short section of a crashed 41mm sanchion tube for test fitting during a machining process. Only needs to be a few inches long. Will pay shipping. Thanks. Craig Mapstone Upstate New York Link to comment Share on other sites More sharing options...
Global Moderator sorkyah Posted September 24, 2019 Global Moderator Share Posted September 24, 2019 Now what are you getting into ATGATT... ATTATT, two acronyms I live by. Link to comment Share on other sites More sharing options...
Premium Member blackout Posted September 25, 2019 Author Premium Member Share Posted September 25, 2019 1 hour ago, sorkyah said: Now what are you getting into A top triple (stock offset) designed to allow standard clip-ons to mount a bit higher. Just bought a boring head for the manual mill at work. Learning more stuff as I go. 1 Craig Mapstone Upstate New York Link to comment Share on other sites More sharing options...
mossrider Posted September 25, 2019 Share Posted September 25, 2019 I look away just long enough to put Carrillo rods and Wiseco pistons in my cart and you're already into trouble... 2 Link to comment Share on other sites More sharing options...
Global Moderator sorkyah Posted September 25, 2019 Global Moderator Share Posted September 25, 2019 Do I have to come down there and smack both of y'all 2 ATGATT... ATTATT, two acronyms I live by. Link to comment Share on other sites More sharing options...
Premium Member blackout Posted September 25, 2019 Author Premium Member Share Posted September 25, 2019 28 minutes ago, mossrider said: I look away just long enough to put Carrillo rods and Wiseco pistons in my cart and you're already into trouble... Ha, Ha! It's going to be a busy winter. Luckily the bike is going inside the porch instead of the garage. I'll be able to work on the bike in my pajamas! lol In the garage, I would have to shovel a snow path to get there after storms. 1 Craig Mapstone Upstate New York Link to comment Share on other sites More sharing options...
twf Posted September 25, 2019 Share Posted September 25, 2019 I got what you need. 3 Link to comment Share on other sites More sharing options...
Premium Member blackout Posted September 25, 2019 Author Premium Member Share Posted September 25, 2019 14 hours ago, twf said: I got what you need. Let me know mailing address and cost, and I'll send a check out. Thanks. Craig Mapstone Upstate New York Link to comment Share on other sites More sharing options...
Premium Member fzar Posted September 26, 2019 Premium Member Share Posted September 26, 2019 22 hours ago, twf said: I got what you need. The Z- Man to the rescue. Link to comment Share on other sites More sharing options...
Spatt Posted September 29, 2019 Share Posted September 29, 2019 On 9/25/2019 at 4:04 AM, twf said: I got what you need. Sh*t Zoran is on here too. Lawd almighty. 1 Get your MT07 & FZ07 racing parts at https://www.robemengineering.com/fz-07-products Link to comment Share on other sites More sharing options...
Premium Member blackout Posted October 10, 2019 Author Premium Member Share Posted October 10, 2019 So, started machining. Going to be a slow process while I have free time at work. Luckily this little mill is rarely used at my work place. Question, do the manufactures generally spec their bikes to even millimeters? My top triple is still on my bike along with fairings so measuring is tricky. I measured a center to center fork spacing of 189.84mm. I'm guessing the true fork spacing is an even 190mm. Does anyone know? Otherwise I'll just measure again this weekend with some of the parts removed. Thanks. Also, is the stock offset 40mm? Thanks. Craig Mapstone Upstate New York Link to comment Share on other sites More sharing options...
mossrider Posted October 10, 2019 Share Posted October 10, 2019 Please read instructions carefully PRIOR to commencing project, some assembly required, batteries not included, results may vary, not responsible for damage, loss of appendage, injuries or municipal fines... What? 1 Link to comment Share on other sites More sharing options...
Global Moderator sorkyah Posted October 11, 2019 Global Moderator Share Posted October 11, 2019 Moss, how dare you share that pic of me in my nightie 1 ATGATT... ATTATT, two acronyms I live by. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now